SECTION 2 – DEFINITIONS
คำชี้แจง - ถ้าไม่กรอกทั้งชื่อ และนามสกุลของผู้ทำข้อสอบ ระบบจะไม่ตรวจข้อสอบให้ - ถ้าทำข้อสอบไม่ครบ ระบบจะไม่ตรวจข้อสอบให้ - เกณฑ์ตัดสินผ่านการทดสอบอยู่ที่ร้อยละ 90 หรือ 27 ข้อขึ้นไป
แบบทดสอบนี้ มีจำนวนข้อสอบ 44 ข้อ หากต้องการเพิ่มจำนวนข้อ ให้เลือก เพิ่มจำนวนข้อเป็น 20 ข้อ 30 ข้อ 50 ข้อ

1. 2.09 What is a datum plate? a. A level metal plate located directly under the reference gauge point to provide a fixed contact surface from which liquid depth measurement can be made. b. A metal plate located next to the gauging point on a tank indicating the reference gauge height. c. A metal plate located close to the gauging point on a tank listing all the relevant tank data d. A level metal plate located at the top of a gauge hatch on a tank from which the gauge height is measured. 2. 2.36 How is Gross Observed Volume (GOV) defined? a. The volume read from the strapping table b. The total volume of all petroleum liquids and sediment and water, excluding free water, at observed temperature and pressure c. The volume read from the strapping table corrected for roof displacement d. The volume used to calculate vessel ratios 3. 2.03 What is ballast? a. Water in the tanks of a vessel used for laundry and other sanitation purposes b. Any water on board a vessel in any tank c. Water that is used to clean cargo tanks d. Water that allows the vessel to maintain stability and to control stress and trim 4. 2.04 What is a permanent ballast tank? a. A tank that contains ballast at all times b. A tank that is designated to contain only ballast c. A tank that is used only to maintain a permanent list condition d. Answers a., b. and c. are all wrong 5. 2.20 How is an all levels sample obtained? a. By submerging an unstoppered sampler to a point near the tank draw-off outlet (suction) level and then raising it, all at a uniform rate, so that it is no more than 85% full on emerging from the liquid. b. By blending upper, middle and lower samples from the same tank. c. By submerging a stoppered sampler to a point as near as possible to the draw-off outlet (suction) level, then opening the sampler and raising it at a rate such that it is no more than 80% full as it emerges from the liquid. d. By submerging a stoppered sampler to the mid point of the product in a tank, then opening the sampler and raising and lowering it at a uniform rate until the sampler is full. 6. 2.10 What is deadwood? a. Wooden cup-case thermometer cases that are no longer fit for use b. Any piece of gauging equipment made of wood (i.e. wooden handles of gauge tapes, cup-case thermometer cases) that have been exposed to chemicals and have been damaged as a result c. Any tank fitting or structural member inside a tank that affects the capacity of the tank d. Answers a., b. and c. are all wrong 7. 2.24 What is the volume of all material in a tank at the observed temperature less the free water called? a. Total Observed Volume (TOV) b. Gross Standard Volume (GSV) c. Gross Observed Volume (GOV) d. Remaining On Board (ROB) 8. 2.41 What has the same meaning as the term innage? a. Ullage b. Sounding c. Outage d. Answers a., b. and c. are all wrong 9. 2.32 What is the name of the document which is given as an official receipt for the cargo on board a vessel? a. Certificate of Quality b. Custom declaration c. Bill of Lading d. Charter party 10. 2.23 What is the total volume of all material in a tank at the observed temperature called? a. Total Calculated Volume (TCV) b. Total Observed Volume (TOV) c. On Board Quantity (OBQ) d. Gross Observed Volume (GOV) 11. 2.16 What is Gross Observed Volume (GOV)? a. The total measured volume of all petroleum liquids, sediment and water, and free water at observed temperature b. The total volume of all petroleum liquids and sediment and water, excluding free water, at observed temperature c. The total volume of all petroleum liquids excluding sediment and water and free water, at observed temperature d. The total volume of all petroleum liquids and sediment and water, excluding free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density 12. 2.18 What is Net Standard Volume (NSV)? a. The total volume of all petroleum liquids, excluding sediment and water and free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density b. The total volume of all petroleum liquids, excluding sediment and water, but including free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density c. The total volume of all petroleum liquids and free water, excluding sediment and water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density d. The total volume of all petroleum liquids and sediment and water and free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density 13. 2.39 How is list defined? a. The difference between the starboard draft and the port freeboard b. The leaning or inclination of a vessel expressed in degrees to port or starboard c. The average of the starboard draft and the port draft expressed in degrees port or starboard d. The difference between the forward and aft draft 14. 2.08 What is clingage? a. The wedge shaped volume of oil remaining in a tank after discharge b. The non-liquid wedge-shaped volume of oil remaining in a tank after discharge c. The cargo that adheres to the internal vertical surfaces of a tank after it has been emptied. d. The ability of a liquid to cling to the inside surface of a container 15. 2.34 What is the name given to the mixture of oil, tank washings, water and sediment collected in a designated ship s tank? a. Polluted oil b. Merchantable oil c. Slops d. Hazardous waste 16. 2.31 What is the term for the amount to be paid by the Charterer if a vessel is delayed beyond the terms allowed in the Charter Party? a. Dispatch money b. Demurrage c. Disbursement d. Penalty money 17. 2.02 What is a hydrometer? a. A device to measure viscosity b. A device to measure hydration c. A device to measure density d. A device to measure water flow 18. 2.28 What term describes a vessel with the forward draft greater than the aft draft? a. Down by the stern b. Trimmed by the head c. Up at the bow d. Listing dangerously 19. 2.05 What does the abbreviation S&W stand for? a. Sand and Water b. Sediment and Waste c. Scale and Water d. Sediment and Water 20. 2.27 What is the Reference Gauge Height of a tank? a. The distance from the tank top to the tank bottom b. The distance from the ullage hatch to the datum plate c. The distance from reference gauge point to the tank bottom or datum plate d. The distance from tank bottom to the ullage hatch 21. 2.12 The density of a liquid will change as its temperature changes. a. True b. False 22. 2.35 What is the Total Observed Volume (TOV) defined as? a. The volume read from the strapping table b. The total measured volume of all petroleum liquids, sediment and water, and free water at observed temperature and pressure c. The volume read from the strapping table corrected for roof displacement d. The volume used to calculate a Vessel Experience Factor (VEF) 23. 2.17 What is Gross Standard Volume (GSV)? a. The total volume of all petroleum liquids excluding free water, water and sediment, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density b. The total volume of all petroleum liquids including free water, water and sediment, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density c. The total volume of all petroleum liquids and sediment and water, excluding free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density d. The total volume of all petroleum liquids including free water but excluding sediment and water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density 24. 2.42 What is load on top? a. The shipboard practice of collecting water and water and oil mixtures resulting from ballasting and tank cleaning operations (usually in a slop tank) and subsequently loading cargo on top of it and pumping the mixture ashore at the discharge port. b. The act of commingling existing onboard quantity with cargo being loaded c. Answers a. and b. are correct d. Answers a., b. and c. are all wrong 25. 2.40 How is free water defined? a. The layer of water present in the tank that is not suspended in the oil b. Any water found on the bob with water paste c. Any water found using the tank gauging equipment d. Any water that is trim corrected 26. 2.38 How is trim defined? a. The same as the draft b. The difference between the forward and aft draft c. The average of the forward draft, the amidships draft, and the aft draft d. The leaning of the vessel to one side 27. 2.21 How is a running sample obtained? a. by lowering an unstoppered sampler from the top of the oil to the level of the outlet (Suction) and returning it to the top of the oil at a uniform rate so that the sampler is no more than 85% full when withdrawn from the oil. b. by lowering a stoppered sampler to the level of the outlet, then opening the sampler and raising it at a uniform rate so that it is about 80% full when withdrawn from the oil. c. by lowering a stoppered sampler to the mid point of the tank contents, then opening the sampler and raising and lowering it at a uniform rate until it is full d. by lowering an unstoppered sampler to the mid point of the tank contents, then raising and lowering it at a uniform rate until it is full 28. 2.44 A US barrel has a volume of? a. 55 US gallons b. 1 cubic meter c. 5 liters d. 42 US gallons 29. 2.01 What does the API Gravity scale indicate? a. Density b. Volume c. Weight in Vacuum d. Ratio of weight to density 30. 2.15 What is Total Observed Volume (TOV)? a. The total measured volume of all petroleum liquids, sediment and water, and free water at observed temperature b. The total measured volume of all petroleum liquids, sediment and water but excluding free water, at observed temperature c. The total volume of all petroleum liquids and sediment and water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density d. The total measured volume of all petroleum liquids excluding water and sediment, at observed temperature ให้ตรวจสอบชื่อนามสกุลว่ากรอกครบหรือไหม่ พร้อมกับตรวจข้อสอบว่าเลือกทำครบทุกข้อหรือไม่ ไม่ครบไม่ตรวจนะครับ

1. แนวข้อสอบ ภาษาอังกฤษ ป.3

2. ประวัติศาสตร์ไทย ม.ปลาย ชุดที่8

3. ข้อสอบเข้ามหาวิทยาลัย เคมี(2546) ชุดที่2

4. แนวข้อสอบ ภาษาญี่ปุ่น ชุดที่1