SECTION 2 DEFINITIONS

คำชี้แจง

- ถ้าไม่กรอกทั้งชื่อ และนามสกุลของผู้ทำข้อสอบ ระบบจะไม่ตรวจข้อสอบให้

- ส่วนนี้จะไม่มีการบันทึกผลสอบ หากต้องการบันทึกโปรดสมัครสมาชิก

- ถ้าทำข้อสอบไม่ครบ ระบบจะไม่ตรวจข้อสอบให้

- ผู้ทำข้อสอบจะมีเวลาในการทำข้อสอบเพียง 30 นาที หากเกินเวลา ระบบจะไม่ตรวจข้อสอบให้

- เกณฑ์ตัดสินผ่านการทดสอบอยู่ที่ร้อยละ 90 หรือ 9 ข้อขึ้นไป

ข้อสอบชุดนี้แสดงผลครั้งละ 10 ข้อ บนเครื่องคอมพิวเตอร์ Desktop

ข้อสอบชุดนี้แสดงผลแล้ว 2170 ครั้ง

ส่วนนี้จะไม่มีการบันทึกผลสอบ และแสดงเฉลยแบบทดสอบ หากต้องการบันทึก และรายงานการทำแบบทดสอบ โปรดสมัครสมาชิก

ข้อสอบชุดนี้จำนวน 44 ข้อ หากต้องการเพิ่มจำนวนข้อสอบ คลิก ทำแบบทดสอบออนไลน์

1. 2.27 What is the Reference Gauge Height of a tank? a. The distance from the tank top to the tank bottom b. The distance from the ullage hatch to the datum plate c. The distance from reference gauge point to the tank bottom or datum plate d. The distance from tank bottom to the ullage hatch
2. 2.43 What is a wall wash test? a. The activity of rinsing the wall of a tank with a solvent and obtaining a sample of the previous product(s) to determine compatibility with the product to be loaded b. The activity of rinsing a tank with clean, fresh water following tank cleaning to ensure that the product to be loaded will not be contaminated c. The activity of washing the walls of a tank to remove all traces of the product previously contained in the tank d. Answers a., b. and c. are all wrong
3. 2.03 What is ballast? a. Water in the tanks of a vessel used for laundry and other sanitation purposes b. Any water on board a vessel in any tank c. Water that is used to clean cargo tanks d. Water that allows the vessel to maintain stability and to control stress and trim
4. 2.09 What is a datum plate? a. A level metal plate located directly under the reference gauge point to provide a fixed contact surface from which liquid depth measurement can be made. b. A metal plate located next to the gauging point on a tank indicating the reference gauge height. c. A metal plate located close to the gauging point on a tank listing all the relevant tank data d. A level metal plate located at the top of a gauge hatch on a tank from which the gauge height is measured.
5. 2.35 What is the Total Observed Volume (TOV) defined as? a. The volume read from the strapping table b. The total measured volume of all petroleum liquids, sediment and water, and free water at observed temperature and pressure c. The volume read from the strapping table corrected for roof displacement d. The volume used to calculate a Vessel Experience Factor (VEF)
6. 2.36 How is Gross Observed Volume (GOV) defined? a. The volume read from the strapping table b. The total volume of all petroleum liquids and sediment and water, excluding free water, at observed temperature and pressure c. The volume read from the strapping table corrected for roof displacement d. The volume used to calculate vessel ratios
7. 2.22 What is a floating roof tank? a. A tank in which the roof floats freely on the surface of the liquid contents at all levels. b. A tank in which the roof floats freely on the surface of the liquid contents except at low levels when the weight of the roof is supported by its legs. c. A tank in which the roof, supported by guide wires, can be adjusted to the required height for safe filling of the tank d. Answers a., b. and c. are all wrong
8. 2.42 What is load on top? a. The shipboard practice of collecting water and water and oil mixtures resulting from ballasting and tank cleaning operations (usually in a slop tank) and subsequently loading cargo on top of it and pumping the mixture ashore at the discharge port. b. The act of commingling existing onboard quantity with cargo being loaded c. Answers a. and b. are correct d. Answers a., b. and c. are all wrong
9. 2.38 How is trim defined? a. The same as the draft b. The difference between the forward and aft draft c. The average of the forward draft, the amidships draft, and the aft draft d. The leaning of the vessel to one side
10. 2.17 What is Gross Standard Volume (GSV)? a. The total volume of all petroleum liquids excluding free water, water and sediment, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density b. The total volume of all petroleum liquids including free water, water and sediment, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density c. The total volume of all petroleum liquids and sediment and water, excluding free water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density d. The total volume of all petroleum liquids including free water but excluding sediment and water, corrected to a standard temperature by the appropriate volume correction factor for the observed temperature and density
ให้ตรวจสอบชื่อนามสกุลว่ากรอกครบหรือไหม่ พร้อมกับตรวจข้อสอบว่าเลือกทำครบทุกข้อหรือไม่ ไม่ครบไม่ตรวจนะครับ

นำแบบทดสอบไปติดที่เว็บของคุณ ครับ

SECTION 2  DEFINITIONS

SECTION 2 DEFINITIONS