SECTION 8 – TEMPERATURE MEASUREMENT

SECTION คำชี้แจง
- ถ้าไม่กรอกทั้งชื่อ และนามสกุลของผู้ทำข้อสอบ ระบบจะไม่ตรวจข้อสอบให้
- ส่วนนี้จะไม่มีการบันทึกผลสอบ หากต้องการบันทึกโปรดสมัครสมาชิก
- ถ้าทำข้อสอบไม่ครบ ระบบจะไม่ตรวจข้อสอบให้
- ผู้ทำข้อสอบจะมีเวลาในการทำข้อสอบเพียง 30 นาที หากเกินเวลา ระบบจะไม่ตรวจข้อสอบให้
- เกณฑ์ตัดสินผ่านการทดสอบอยู่ที่ร้อยละ 80 หรือ 8 ข้อขึ้นไป
ข้อสอบชุดนี้แสดงผลครั้งละ 10 ข้อ บนเครื่องคอมพิวเตอร์สมาชิก
ข้อสอบชุดนี้แสดงผลแล้ว 2997 ครั้ง
ส่วนนี้จะไม่มีการบันทึกผลสอบ และแสดงเฉลยแบบทดสอบ หากต้องการบันทึก และรายงานการทำแบบทดสอบ โปรดสมัครสมาชิก 
ข้อสอบชุดนี้จำนวน 55 ข้อ หากต้องการเพิ่มจำนวนข้อสอบ คลิก ทำแบบทดสอบออนไลน์
1. 8.02 Does API MPMS Chapter 7/ISO 4268 make any references to the construction of portable electronic thermometers?
    a. Yes
    b. No
    c.
    d.
2. 8.35 Which ISO standard covers temperature determination?
    a. ISO 3171
    b. ISO 4268
    c. ISO 4512
    d. ISO 4266
3. 8.24 According to ISO 4268 [API Chapter 7] the minimum amount of time a stationary PET should stay in a product with a density greater than 935 kg/m3 is ?
    a. 10 minutes
    b. 1 minute
    c. 5 minutes
    d. Until the readout doesn t vary by more than 0.1°C [0.2°F] for 30 seconds
4. 8.51 The immersion time for a cup-case assembly is minimized by continually raising and lowering the assembly 0.3m [1 foot] above and below the desired temperature measurement point.
    a. True
    b. False
    c.
    d.
5. 8.10 To what increment should the display of a portable electronic thermometer be capable of reading?
    a. 0.5 °F or °C
    b. 0.1 °F or °C
    c. 1.0 °F or °C
    d. 0.25 °F or °C
6. 8.54 According to API MPMS Chapter 17.1, the preferred instrument for taking temperature is?
    a. A liquid-in-glass thermometer
    b. A portable electronic thermometer
    c. An in-line temperature probe
    d. A preferred instrument is not specified
7. 8.11 Which standards address the earthing (grounding) of portable electronic thermometers?
    a. API MPMS Chapter 7/ISO 4268
    b. API MPMS Chapter 3/EI HM4
    c. API MPMS Chapter 8.1/ISO 3170
    d. API MPMS Chapter 17.9/EI HM49
8. 8.36 A liquid-in-glass thermometer with a range between 60°F and 180°F and must be accurate to within?
    a. ± 1.0 °F
    b. ± 0.5 °F
    c. ± 0.1 °F
    d. ± 0.25 °F
9. 8.44 When using a liquid-in-glass thermometer in a cup-case assembly to measure a product with density of 904 kg/m3 [API gravity 24.9] what is the minimum length of time the thermometer should be immersed in the liquid when the assembly is in motion during the measurement process?
    a. 5 minutes
    b. 10 minutes
    c. 20 minutes
    d. Until the readout doesn t vary by more than 0.2 °C for 30 seconds
10. 8.18 If only one temperature is required where should this temperature be taken from?
    a. The middle of the upper third
    b. The middle of the liquid level
    c. The middle of the lower third.
    d. Use a side readout thermometer
ให้ตรวจสอบชื่อนามสกุลว่ากรอกครบหรือไหม่
พร้อมกับตรวจข้อสอบว่าเลือกทำครบทุกข้อหรือไม่ ไม่ครบไม่ตรวจนะครับ
นำแบบทดสอบไปติดที่เว็บของคุณ ครับ

EDUCATION RESEARCH | หน้าแรกข้อสอบ | เข้าระบบ | สมัครสมาชิก | สร้างข้อสอบ | แชร์ข้อสอบ
แนวข้อสอบบรรจุครูผู้ช่วย | TOEIC Online | IELTS Online | SAT | TOEIC | IELTS